This blog post will show you how to change your door lock on your car. You will need a new door lock, a screwdriver, and a few other tools.
- 1 Preparing for the Job
- 2 Removing the Old Lock
- 3 Installing the New Lock
- 4 Finishing Up
Preparing for the Job
Changing your car’s door lock can be a daunting task if you’ve never done it before. Before starting the job, it’s important that you gather all the necessary tools and materials you need. Make sure you have all the right tools such as a screwdriver, wrench, and drill bits. Additionally, you should have a replacement door lock and some lubricant on hand. Let’s get started preparing for the job.
Gather the tools and materials needed
Changing a door lock can be a daunting task. Before attempting to replace it, it is important to make sure you have collected all of the necessary tools and materials. Depending on the make and model of your car, the materials needed may vary slightly.
You will likely need: a new lock cylinder; Phillips head screwdriver; flat-head screwdriver or small pry bar; hammer; pliers; lubricant such as WD-40 or silicone spray lubricant; and a blank key for your vehicle (It is recommended to get this prior to starting the job, as most locksmiths will require identification for cutting new keys). Additionally, if you are replacing the cylinder due to loss or theft, you should also have 2 copies of any vehicle registration and proof of insurance documents in order to obtain a replacement key from an automotive locksmith.
Once you have gathered all necessary tools and materials, you can begin replacing your lock cylinder. Be sure to follow your manufacturer’s instructions closely during this process as procedures may vary between different models of cars.
Research the type of lock and key you need
Before you begin the process of changing your car’s door lock, it’s important to Test the Lock and know exactly what type of lock and key you will need for the job. There is a wide variety of car door locks available in the market, so it’s important to be sure you have the correct one for your make and model before commencing the job.
Research online or contact a car repair specialist to find out more details about which type of lock and key your vehicle should use. It may be beneficial to purchase a new lock and key set in advance as this can save time later on. Additionally, discuss any complications that may occur with a professional before attempting to install or replace any part of your vehicle’s locking system. Testing the Lock beforehand will ensure that you have the right type for your car.
Removing the Old Lock
Changing your car door lock is a relatively simple process, but it’s important to make sure you follow the proper steps to ensure a secure and safe installation of your new lock. The first step in replacing your car door lock is to remove the old lock. This step is necessary in order to be able to install the new lock in its place. To remove the old lock, you will need a few basic tools to help you along.
Identify the type of lock and key
To successfully change the lock on your car, you’ll need to identify the type of lock and key in use. Many cars come with a standard cylindrical “double-sided” key which can be seen in many configurations including pin cylinders or as an electronic or transponder key system. Each of theselock types requires different steps to be taken when it comes to removing the old lock and installing a new one. Additionally, some newer model cars utilize a “smart” or proximity locking system that requires specialized tools and processes in order to install a new lock.
Once you have identified the type of lock and key used on your car, you will need to gather all the necessary tools for the job, such as a screwdriver set, various wrenches, tape measure, locksmith’s tools (if applicable), electrical wiring connectors (if applicable), lubricating oil (if applicable) and graphite powder (if applicable). If you are replacing a standard cylinder lock then chances are you won’t need any specialized locksmith’s tools. However, if more advanced security systems such as smart locks are used then you may require additional specialist equipment.
Remove the old lock and key
In order to remove the old lock and key from your car, you made need some special tools and supplies. Start by gathering the necessary items you’ll need, such as a flat-head screwdriver and vice grips (some locks use small screws to hold the key cylinder in place). If you don’t have these items, they can be purchased at any local hardware store or online. You may also need some lubricant, such as oil or WD-40, and graphite powder (if your lock needs extra lubrication).
Once you have all of your supplies gathered, it’s time to remove the old lock from your car. Start by studying the door panel of your car to determine how many screws are used to hold it in place. Remove each screw one at a time using the flathead screwdriver. Once all of the screws are removed, carefully remove the panel from around the lock.
Next, use your Vice Grips or other special tools included with your new lock set to unscrew and remove any screws that secure the old key cylinder in place. Now slip off any retainer rings or soft washers that may be protecting the cylinder before attempting to lift it out of its opening. Once successfully removed, review any instructions included with your new lock set before tightening everything back together again or replacing parts as necessary. Finally, make sure that everything is securely fastened before testing out your new door lock on your car!
Installing the New Lock
If you need to replace the Door Knob lock on your car, the first step is to install the new lock. Depending on the model of your car and the type of lock you choose, the installation process may vary. This article will provide step-by-step instructions on how to safely and correctly install a Door Knob lock on your car.
Install the new lock and key
When the old lock has been removed, you will need to install the new lock and key. Begin by lubricating the inside of the door lock, using a silicone lubricant or other tree oil-based product. This step is important to help reduce future friction and ensure that the lock operates properly.
Next, slide the cam into position and secure it with a screw or metal clip as necessary. Insert the spring washer that came with your new lock onto one of the holes in the backside of your door’s metal plate. Use a flat head screwdriver to press down on it until it is firmly in place.
Then, carefully insert the plug into its cylindrical plug housing sleeve and ensure that it sits firmly in place within its groove. Slide your key cylinder over the plug so that its grooves align snugly with those on top of your plug housing sleeve. Once these are connected, you can use your key to slowly turn this cylinder clockwise until you hear a click as all pins line up correctly.
Finally, insert your key into its corresponding slot of your car’s actual door lock cylinder and use a pair of vice-grip pliers if necessary to adjust its placement until appropriate pressure is found against all angling pins within this slot. With all parts securely fitted together, test out your new lock by pushing your key down while still inserted into its slot and attempt pushing or pulling open both sides of this door’s locking mechanism to verify proper installation has been successfully achieved!
Test the new lock and key
Before completely installing the new lock, it is important to test to ensure that the lock and key work properly. Insert the Cut the Key into the lock, turning it in both directions. Try unlocking and locking the mechanism several times. If turning in different directions causes any obstruction or difficulty, make sure to clean or lubricate the device. To be safe, repeat this process with all of the locks in your car’s security system.
Once all locks are tested, you can fully install them. Remove any existing bolts from each side of your vehicle’s door; then insert a few screws included with your new lock fastening it securely on both sides. Reconnect any electrical components included with new lock if applicable. Once all locks are installed on both sides of the door, test again to make sure they open and close properly using your Cut the Key and other needed keys (i.e.: chip keys if applicable).
Now that you’ve finished replacing the door lock on your car, you can feel confident that your car is now more secure. However, it’s always important to remember to test the new lock to make sure it’s working properly. In order to test the lock, you will need to try and open the door from both the inside and outside. If everything works properly, then you can now rest assured that your car is now even more secure.
Clean up and dispose of old lock and key
Once you’ve successfully installed the new door lock and tested it to make sure it works, take a few moments to clean up. Make sure you remove any sawdust or other debris from the inside of your car door and vacuum out any excess dirt or filings. Depending on how damaged your old lock was, you might find it necessary to utilize a putty knife or toothpick to scrape away stubborn pieces of metal from the area around the lock cylinder.
When you’re finished cleaning up, take time to properly dispose of the old lock and key. Disposing of these items in an environmentally responsible manner helps protect our planet and keeps everyone safe. You can pull apart the components of your old lock (plastic, springs, screws etc.) once you have removed them, then place them in a secure receptacle for recycling. If your city offers hazardous waste disposal services, bring your old lock there for proper disposal.
Test the new lock and key again
Once the Replace Door Knob has been successfully installed in your car, it is important to test the new lock and key one final time. Make sure to insert the key into the knob and turn it, confirming that it is able to unlock and lock properly. In addition, you may want to remove the key and then insert it back into the knob a few times, ensuring that no issues arise with individual use. Once confirmed that your new door knob works as intended, you can proceed to reattach any paneling or close any areas you had opened earlier in order complete the repair process.
Checkout this video: