Skip to content

How to Change Your Front Door Lock

This article is a collaborative effort, crafted and edited by a team of dedicated professionals.

Contributors: Muhammad Baballe Ahmad, Mehmet Cavas, Sudhir Chitnis, and Zhen-ya Liu.

✓ Verified & Tested Information

If you’re looking to change your front door lock, follow these simple steps. You’ll be able to do it in no time!

Gather Your Supplies

Changing your front door lock is an important step in home security and safety. To ensure you have all the supplies for the job, you’ll need to gather the necessary components before beginning. Gather a new door lock, a Phillips head screwdriver, a flat head screwdriver, a drill, and a measuring tape. With all your supplies ready, you’ll be able to start the job.

Determine the type of lock you need

When changing your front door lock, you must first determine the type of lock and key you need. You will also have to decide if you want a basic cylinder doorknob lock or a more complex deadbolt. Both types have their own benefits and drawbacks, so carefully consider what you need in terms of functionality and lockset.

Cylinder doorknob locks are easy to install and provide adequate security if they come with an anti-pick or anti-bump mechanism. Deadbolts are usually more secure because they require a key on both sides of the door. In general, it is best to purchase multiple locksets for each entrance so that all doors feature the same level of security.

When purchasing your new lock set, make sure it meets the standard for ANSI/BHMA A156.2 Grade 2 security rating as this is generally seen as a safe option for home use. Once you’ve chosen the type of lockset needed, consider any additional features such as finish, style and keying requirements like keyed alike or master keying before making your purchase.

Purchase the necessary supplies

Changing the lock on your front door may seem like a daunting task, but with the right supplies and a few simple steps, you can easily complete the project in no time. Before you get started, it’s important to have all of the necessary supplies on hand.
Here is a list of items that you will need to perform the lock change:
-A new lock set: Make sure that you choose a door lock that is designed for exterior use and buy one that meets your home’s security requirements. You should also check for any special drilling or installation needs for your particular model.
-Screwdriver: Depending on which lock set you purchased, you may need either Phillips head or flathead screwdrivers to remove any screws and pry out existing components.
-Socket Set: If required by your particular model, you will need a socket set with corresponding bit sizes to remove any existing hardware and install new locksets.
-Cordless Drill: This may be needed if the door requires more than normal drilling before installation. Be sure to choose one with adjustable speeds and power settings so that your drill can handle different types of surfaces and materials (e.g., wood, metal). It’s also helpful to have multiple drill bits in various sizes.
Taking time up front to ensure that all of these items are in place before starting a job like this can make it run much smoother as well make it much easier when it comes time for installation of the new lockset!

Remove the Existing Lock

The first step in changing your front door lock is to remove the existing one. Before you get started, you’ll need to make sure you have the right tools and materials. You’ll also want to be sure that you’re wearing safety goggles and gloves to protect your eyes and hands from sharp edges. Now, you’re ready to start removing the old lock.

Remove the screws from the door

To begin removing a lock from a door, start by removing the screws located on the edge of the door. These screws typically hold the latch in place and can be unscrewed with a small Phillips-head screwdriver or a flat-head. Be sure to take note of where each screw came from so that you can replace them correctly once the lock has been removed.

Once all of the screws have been removed, you should have access to the latch. At this point, if necessary, use a flat-head screwdriver or another small tool to gently pry up any plugs or rivets that may be holding it in place. Once these items have been removed and all screws taken out of the door, you are now ready to remove your existing lock.

Take off the existing lock

Before you can install a new lock, you must first Cut the Key to remove the existing lock. If the door handle is locked, you will need to unlock it before you disassemble it. Depending on the kind of handle set on your front door and your preference as to how quickly you want to take off the existing lock, there are a few different ways to accomplish this task.

If the front door has a lever-style or knob-style handle that comes off easily with a Phillips head screwdriver, begin by sliding off the faceplate behind your handle. This will expose a series of screws which allow you to Cut the Key and take off the existing door lock assembly. Loosen these screws until they come out easily and then remove any other screws that may be holding in place other components such as levers or knobs. Carefully pull out all components one at a time and discard them safely when finished with each one.

If your front door has an older style deadbolt or knob set that is more difficult to remove, consider using either a drill or reciprocating saw with bi-metal blades designed for wood cutting in order to Cut the Key and take off the entire assembly quickly while still maintaining safety protocols such as wearing safety glasses and hearing protection. Make sure that all power tools are disconnected prior to beginning any dismantling tasks; disconnecting power supply immediately if anything goes wrong during use is essential for safety protocols.

Once all components have been safely removed from your front door lock, ensure that all spots where old locks were installed are clear and ready for new installation. Wipe down surfaces using clean cloths or paper towels with warm water before beginning any installation process as dirt build up can cause delays in installation time and also prevent planned finishes from looking their best when completed project is revealed.

Install the New Lock

If you’re looking to change your home’s front door lock, you’re in the right place. Installing a new lock is actually quite simple. All you need is a few basic tools, a new lock and the old one removed. In this guide, we’ll take you through the steps of how to properly install the new lock on your front door. Let’s get started.

Place the new lock in the door

Once you have the door prepped, take the new lock and place it into the door. To ensure best positioning for secure locking, align the latch of the deadbolt halfway between the top and bottom of the edge of your door. Make sure to adjust as needed so that it is completely centered for even pressure when latching. Check that there is a slot on one side of your lock for a flat head screwdriver, as most locks require some adjustment after installation. It may be helpful to use masking tape to mark where you want your screws to line up before drilling; this will help keep holes straight and make securing it in place easier.

Secure the new lock with screws

Secure the new Replace Door lock with screws that are appropriate for the door, the size of the lock, and your preference. On most locks, it is easiest to use two screws. To safely install, start by marking where you want to place the holes for each screw and then pre-drill with a drill bit smaller than the screws. If you have old, rusted screws that need to be removed, use a lubricant spray or WD-40 to loosen them up before unscrewing them.

Once you have pre-drilled the holes for your new Replace Door screws, add anchors if needed. Anchors are used when drilling into concrete or brick and help secure and stabilize your new lock to give it longevity. Most locks come with their own accompanying anchors which should be used rather than any generic anchors purchased at a store or online. Once your anchor is properly inserted into the hole, add a washer over top of it then insert one screw into each hole and hand tighten until secure.

Do not overtighten or use power tools on this step as this may cause damage or strip out threads in your new Replace Door lock.. After hand tightened each screw as much as possible check that your new lock moves smoothly in both directions (opening and closing) before you call this installation complete!

Test the Lock

Before you begin to change your front door lock, it is important to test the existing lock to make sure it is working properly. You can do this by trying to turn the key to the right and left to determine if the lock is responding correctly. If it is not, you should have the old lock replaced before you begin to change it. This will ensure that your new lock is as secure as possible and will work as intended.

Test the lock to ensure it is working properly

Before installing and using your new lock, it is important to first test it. Testing your lock will allow you to check that the components are all functioning correctly, thus ensuring the security of your home. To test the lock, begin by inserting the key into the keyhole. If the key fits properly and turns smoothly, we can move onto testing the spring bolt mechanism (or deadbolt if you have one).

If you have a lever handle lock, grip it firmly and push down on the handle. This should retract and extend the latch fully, clicking into a locked position when released. If you have an external cylinder or a knob converted from one type of locking system to another (such as from a single thumb-turn operation to a two-point) use a car key or other long object such as an Allen key to actuate both knobs/cylinders at once. The door should now be locked in place. Then, use your key again to unlock it. Lastly, repeat this several times while listening for any unusual noises or movements – things like grinding or sticking may indicate that something is amiss with your new lock installation and needs attention before proper use begins.

Make any necessary adjustments

Once your lockset is installed, it’s a good idea to test the lock for proper operation. Start by checking that the deadbolt moves freely and works in both directions when using either the key from the outside or the thumb-turn from the inside. Inspect around the perimeter of the door at each offset where the lockset is mounted, looking for any signs of misalignment or binding due to nail heads contacting either component. If you find any areas that appear to be binding or not lining up properly, you may need to make some small adjustments.

To fix minor errors in alignment, you can use a screwdriver or Allen wrench (provided with some locksets) to gently nudge one of the components slightly into proper alignment with its counterpoint. If there is contact due to a slight bend in one piece, use even less force as this will create extra friction and impede normal operation which can cause damage over time.

If adjustments don’t fix your issue, you will likely need to remove and reinstall your lockset taking particular care upon reinstallation that everything lines up properly and securely before turning any screws tight.

Clean Up

Changing your front door lock is an important task that requires some preparation. Before you try to remove the old lock, you will need to clean up the area around it. This includes dusting, vacuuming, and clearing away any debris. After this is done, you should be able to remove the old lock and replace it with a new one easily. Let’s look at the steps involved in cleaning up the area around the door lock.

Remove any debris from the installation

Before you begin to install the new lock, it is important to clear any debris from the area around the door and lock installation. Begin by removing any existing keys or knob covers that are on the door. Make sure to remove all screws and other pieces so that you can see any obstructions in the installation area. Once all remaining pieces have been removed, use a damp cloth or paper towel to clear away any dirt, dust or debris that could interfere with the installation. If there is rust residue from old locks, use a steel brush and cleaner to remove it. If there is paint on the surface of your lock plate or spindles, gently scrape away with a razor blade. Be sure to work carefully in order not to damage your door frame. After all obstructions have been cleared away, you will be ready to install your new lock components.

Clean up the area around the door

When changing a front door lock, you should take care to clean up the area surrounding the door to ensure it is safe to work. First, clear away any debris by vacuuming or sweeping the area around the frame, then using an all-purpose cleaner to wipe down all surfaces and remove any dried paint or other substances. When cleaning up, be careful not to get anything in your eyes or on your skin – wear safety glasses and protective gloves if necessary.

Once the area is tidy, inspect the door frame itself for any damage or signs of wear and tear. Ensure that screws are tight and properly secured, hinges are maintained and seals are intact so that the door will securely close after installation of a new lock. If you notice cracks or holes in the frame where air can flow through freely, you may want to consider making repairs before moving forward with replacing the lock. Finally, make sure that screws have not been tampered with, as tampering could enable someone to open your front door without using a key.

How to Change Your Front Door LockCheckout this video:

Share this Article