Skip to content

How to Lock a Combination Door Lock

This article is a collaborative effort, crafted and edited by a team of dedicated professionals.

Contributors: Muhammad Baballe Ahmad, Mehmet Cavas, Sudhir Chitnis, and Zhen-ya Liu.

✓ Verified & Tested Information

If you’re looking for a little extra security for your home or office, a combination door lock is a great option. But if you’ve never used one before, the process of Cut the Key setting the lock can seem a bit daunting.

Never fear! In this blog post, we’ll walk you through everything you need to know about how to lock a combination door lock. We’ll cover the basics of how the locks work and what you need to do to Cut the Key set your own personal combination.

Gather the Necessary Materials

Before beginning the process of locking a combination door lock, it is essential to have all the necessary materials and equipment. Depending on the type of lock, you will need specific tools to complete the task. This could include a screwdriver, a snap-lock tool, and a set of paperclips. Additionally, make sure you have the combination code. With the right materials, you can proceed to the step of actually locking the lock.

Gather a flathead screwdriver

Before attempting to lock a combination door lock, it is important to ensure that you have all the necessary materials. The most essential tool when it comes to combination door locks is a flathead screwdriver. This tool must be long enough to reach the screws located inside the housing of the lock mechanism. In order to access these screws, you may need to remove any trim panels that are present around the lock before turning them with your screwdriver. Additionally, you will want to check your combination door lock beforehand and make sure that all its parts are in place and functioning correctly. If any parts appear worn or damaged, you should contact a locksmith for repair or replacement before attempting to operate the lock yourself.

Gather a Phillips head screwdriver

To begin, you will need to gather the necessary materials. One of these items is a Phillips head screwdriver. This can be acquired easily at any hardware store. Make sure you purchase a #2 Phillips head screwdriver that is also magnetic tip as this will help you to insert and remove the screws with ease and minimal effort. Once you have your tool, locate the two screws on either side of the door handle that are used to secure it in place. Carefully remove these two screws with your Phillips driver and set them aside in a safe container such as a plastic bowl or bag for later use.

Gather a paperclip

Before attempting the lock your door, you will need to gather the necessary materials. First, find a paperclip that is flexible yet strong enough to open the lock. A thicker or lined paperclip often offers more stability while trying to open the combination lock and is highly recommended as an alternative. Once you have found your desired paperclip, bend it into a straight line by using pliers if needed. Be careful not to change the shape of the paperclip too much as this can render it useless in opening your combination lock.

Remove the Inside Cover

Removing the inside cover of a combination door lock is the first step in learning how to lock a combination door lock. It is essential that the cover is completely removed in order to access the lock’s inner components. It is also important to understand that the inside cover cannot be reattached unless the lock is locked in place, which will be covered later in this article. This section will provide a detailed guide on how to remove the inside cover of a combination door lock.

Locate the screws on the inside cover

The first step to unlocking a combination door lock is to locate the two screws on the inside cover. These screws are typically found either at the top of the lock, or below the spinning disk. Depending on your particular lockset, you may need either an allen key or a regular slim head screwdriver for this step. Once you find and remove these two screws, you will be able to access the locking mechanism of the door lock. It is important to be careful as you remove these screws and take care to not let them fall down into the device as this could lead to a jam. Once all of the security screws have been removed, then you will be able to unlock your combination door lock in just a few steps.

Unscrew the cover using the appropriate screwdriver

To remove the inside cover of a combination door lock, you will need a screwdriver that is sized to fit the screws holding the cover in place. Some models may require a Phillips head screwdriver and others may require a flat head screwdriver. While removing the screws, take care not to strip them by applying too much pressure.

Once all screws are removed, gently pry off the inside cover and set it aside for use when reassembling. You will now be able to find your combination lock’s reset button or lever located in one of two places: either inside the body of your combination lock or directly behind your code dialer. Depending on your model, you may need to insert a thin tool (a paper clip works well!) into this hole so that you can press down on the button or lever and reset your code. Once completed, reassemble your lock by replacing the inside cover and fastening all screws tight and flush against it.

Remove the cover to expose the lock mechanism

The first step to locking a combination door lock is to remove the inside cover. Depending on the manufacturer, this can be achieved in various ways. Some covers are held together with small screws that secure it to the door frame, while others may require a flathead screwdriver or other tool to pry off. Before you begin, make sure that all screws are completely removed and then carefully pull off the cover and set aside. Once the cover has been removed, you will be able to see the lock mechanism itself and should be able to decipher how it operates. From here on out, depending on whether it is a dial or push-button model, the instructions will vary slightly for each one.

Locate the Reset Button

Knowing how to lock a combination door lock can be a handy skill to have in your arsenal of home security tricks. The first step in resetting or programming your combination door lock is to locate the reset button. This button is typically located near the bottom of the lock and is usually a small, light colored button, but it can vary depending on the manufacturer. Once you have located the reset button, you can move on to the next step.

Locate the reset button on the lock mechanism

A combination door lock is an excellent way to secure your home or business and give you peace of mind. However, if you ever forget the combination, it can be difficult to open the lock. One way to unlock a combination door lock is to locate the reset button on the back side of the lock mechanism.

When you press down on this reset button with a pen or paper clip, it should activate a release lever inside which will allow you to open the door without typing in any codes. While this can be a quick and easy fix to open a door, remember that resetting your combination will require you to choose a new one so keep this in mind before selecting your code!

In most cases, You’ll need access to either side of the door in order for this option to work. It’s important that you check for any screws or panels that need unscrewing prior to resetting; otherwise, you may damage the unit. Once access is obtained and all necessary steps have been taken, press down hard on that small red button on the back side of your lock mechanism with either a pen or paper clip – until everything falls into place and starts working again!

Press and hold the reset button

The reset button is located on the back of the lock, to the right of your current combination. To reset the combination, press and hold down the reset button and enter your desired 4-8 digit combination code. Release the reset button, then turn the door handle to your left. If you have entered your code correctly, you should be able to open and close the door. However, if it does not work, try entering a different combination. It may take several attempts before you find one that works for your particular lock model.

Before entering a new code, it is important to make sure that all of the numbers are placed on a clean surface as any dust or dirt particles can cause them to stick inside the lock mechanism. As an added precaution, test each number in each position before pressing down on the reset button so that you can ensure they are working properly during each attempt.

Set the Combination

Setting the combination to your combination door lock is an important step in the locking process. The combination needs to be meaningful and easy to remember but also secure. In this section, we’ll discuss how you should go about setting the combination for your combination door lock, and the tips you should keep in mind when doing so.

Use the paperclip to turn the dial to the desired combination

Once you have found the location of the reset lever, simply insert a paperclip into the hole and turn the dial clockwise rapidly until it stops. This will release the lock from its current combination and will enable you to set a new one. Next, decide on your new combination and set it on your lock. To do this, turn the dial counter-clockwise until it comes to each number of your combination. When setting up your combination lock, make sure that each of the numbers falls easily between 0 – 39 – don’t worry if they are not exact but they should all be close together. As you come to each number in your combination make sure that you stop by turning slowly – never force the correct number onto the lock while in motion (this could damage important inner components of your lock). Once you have successfully reached each number in your desired combination turn back to 0 until it clicks and locks into place. Your combination door lock is now ready for use with its new code!

Release the reset button

On most combination door locks, there’s a reset button on the back of the lock that you’ll need to press in order to set your new combination. This is also called a reset lever or shackle release.

To begin, locate and press the reset button using either a pen or key. You’ll need to apply constant downward pressure while holding it in place until you reach the desired combination. In some locks, you may need to turn the knob at the same time in order for the reset button to properly engage.

Once your desired combination is set, please make sure to double-check your combination by testing it multiple times before returning your door knob into its original position and releasing the reset button. Congratulations – you are now ready to use your new combination door lock!

Reattach the Inside Cover

Once you have set the desired combination on a combination door lock, it’s necessary to reattach the inside cover. This is the easiest part of the process and simply requires the alignment of the cover over the face of the lock and the secure mounting of the cover to the door. Let’s look at the steps for reattaching the inside cover of a combination door lock.

Align the cover with the lock mechanism

Before you begin reattaching the inside cover to your combination lock, it is important to take your time and make sure everything is properly aligned. Start by closing the open shackle first. Make sure the shackle end is placed snugly into its proper position in the locking mechanism. This should be done carefully to avoid damaging any of the internal components of your door lock.

Once secure, move on to aligning the cover with the lock mechanism itself. Lift up on one side of the inside cover and slide it over its corresponding hook so it fits snuggly in place. Carefully repeat this process for all hooks until you have completely reattached all four corners of the inside cover. It’s important to ensure that each hook snugs intot he corresponding groove on the inner edges of your door lock mechanism before continuing with step three-securing the screw!

Test the Lock

Testing the lock is an important step when it comes to any kind of door lock, especially a combination door lock. When testing the lock, you should make sure that it opens and closes securely, and that the combination you enter is the correct one. This will ensure that the lock is secure and can offer the best protection. Let’s take a look at how to test a combination door lock.

Enter the combination to test the lock

Once a combination door lock has been installed, it is often helpful to test the lock to make sure it is securely locked and that the combination code was correctly entered. To do this, you’ll need to enter the code and then turn the knob or lift the handle on the outer side of the door. If the door does not open, then you know that your code has been successfully entered and that your door is securely locked.

If, however, you find that the knob turns or handle lifts when you enter your code, then there may be a problem with either your combination entry or with how your lock was installed. Make sure to consult with a professional locksmith in order to properly inspect and assess any problems before attempting any repairs yourself. It’s best not to risk any damage being done to your lock as improper repair can potentially cause further issues.

How to Lock a Combination Door LockCheckout this video:

Share this Article