Skip to content

How to Reset Your Bosch Alarm System

This article is a collaborative effort, crafted and edited by a team of dedicated professionals.

Contributors: Muhammad Baballe Ahmad, Mehmet Cavas, Sudhir Chitnis, and Zhen-ya Liu.

✓ Verified & Tested Information

Get step-by-step instructions on how to reset your Bosch alarm system . If you have a problem with your Bosch alarm system, resetting it should be your first step.

Preparation

Resetting your Bosch alarm system requires preparation and the right tools. It is recommended that you have a basic understanding of electrical wiring and the general layout of your alarm system before attempting to reset it. It is also important to have the right equipment, such as a screwdriver, a ladder, and a voltage tester. Once you have gathered the necessary tools and knowledge, you can then begin the process of resetting your Bosch alarm system.

Locate the alarm system’s user manual

Before attempting to reset your Bosch alarm system, it is important to consult the user’s manual in order to properly configure and troubleshoot the system. The manual should contain specific instructions on how to reset the system and should always be kept handy in case problems arise. Additionally, it is recommended that a copy of the manual be kept away from the alarm control panel in case of theft or damage. Furthermore, the manufacturer’s website may also prove useful when it comes to obtaining updated instructions for resetting the Bosch alarm system.

Gather the necessary tools

To properly reset your Bosch alarm system, you will need the following tools on hand: a flathead screwdriver, an electrical screwdriver, an Ohmmeter (for testing doors and control pads), a door monitor switch tester, and a tape measure. Make sure you have access to these items before you begin the reset process.
In addition to these specific tools for working with your Bosch system, it’s important to take safety precautions when working with any electronic device or alarm system – always unplug the power when working with wiring and ensure that all components are secure before continuing. It’s also recommended that you create a document of all settings prior to making changes to ensure they can be restored in case something goes wrong during the reset process.

Disconnect the Power Source

Resetting your Bosch alarm system is a simple and easy process. The first step is to disconnect the power source from the alarm system. For this step, you will need to locate the power box and turn off the circuit breaker that supplies power to the alarm system. After you have done this, you will be ready to begin the reset process.

Unplug the alarm system’s power cord

The first step to resetting your Bosch alarm system is to unplug the power cord from the electrical outlet. Insert a pen or other pointed object into one of the two slots on the side of the alarm system, then press down firmly. This will disconnect power to the device and allow you to safely begin your reset. After it has been disconnected, wait 10 seconds before reconnecting power. Once two minutes have passed, your alarm system will be successfully reset and ready for use.

Remove the batteries

Before you can reset your Bosch alarm system, you must disconnect the power source which is connected to your system. This process will vary depending on if you have either a hardwired or wireless system.

If you have a hardwired system: The power supply is usually connected via a two-pronged plug that attaches to the wall and your Bosch alarm/control panel. Unplug the unit from the wall outlet before attempting to reset the alarm.

If you have a wireless system: In most systems, disconnecting the batteries is all that is necessary in order to restore power and reset your Bosch alarm. To remove any battery connections, twist each battery slightly in a counterclockwise direction and then pull it out of its holder. The batteries will look like AA or 9-volt battery cells and are typically located inside the control panel itself or near it in an accessible way (not behind drywall etc.). Once all of the batteries are removed, press the “reset” button generally found at the top of function dials on Bosch systems.

Reset the Alarm System

Reseting your Bosch alarm system can be a fairly simple task, but it is important to understand the process so that your system can be reset properly. In this guide, we will provide step-by-step instructions on how to properly reset your Bosch alarm system so that you can continue to securely protect your home.

Access the alarm system’s control panel

To reset your Bosch alarm system, the first step is to access the control panel. This will usually involve either entering a code into the numbered keypad or using a physical key switch. You should refer to your alarm system’s instruction manual for detailed instructions on how to access the alarm’s control panel. Then follow the steps below:

1. Locate and press the “Reset” button which is typically located near other control buttons.
2. Enter your four-digit security code as instructed in your user manual; then confirm that you want to reset and/or reactivate your Bosch alarm system by pressing “OK.”
3. Listen for three beeps, indicating that the reset button has been successfully activated, and then leave it alone fot five minutes until it performs a safety check before restarting.
4. Once complete, your alarm system will now be reset and ready to use again

Locate the reset button

When troubleshooting your Bosch alarm system, it is important to know where the reset button is located in order to reset the alarm. Different models of Bosch alarms may have different locations, so it is wise to familiarize yourself with the location of your reset button prior to trying to reset it.

On the top right hand side of your main control panel you will find a small red switch which serves as the Bosch alarm system reset button. This can be identified by the label “RESET.” Once this switch has been identified, please move on to Step 2.

It should be noted that on some newer models of Bosch alarms, you will need to press and hold down the reset button for up to 10 seconds before releasing in order for it to take effect. In situations such as this, make sure not let go until you have heard a single (positive) beep coming from your control panel or display.

Press and hold the reset button for 10 seconds

For most Bosch alarm systems, you will need to press and hold the reset button for 10 seconds to reset your system. If your Bosch alarm system requires a longer period of time, check the product manual for instructions. When you are finished, press and hold the reset button again until you hear a beep, indicating that the system is now reset. If your Bosch alarm has an indicator light that lights up when it is connected to power, it should now return off as confirmation that your system has been successfully reset.

It is important to remember that after the system is reset, all previous settings will return back to their original manufacturer defaults. This means any customization of sensors and settings previously made by a security professional or yourself may need to be manually re-programmed in order for your alarm system to function properly.

Re-Connect the Power Source

Resetting your Bosch alarm system requires you to re-connect the power source. This means you will need to reconnect the power source to the alarm system. When you are ready to reset your Bosch alarm system, you will need to make sure that you have unplugged the power source from the wall. After that, you will be able to proceed with resetting the alarm system.

Replace the batteries

Replacing the batteries in your Bosch alarm system is an essential step for resetting the device. After any power outage, blackout, or other loss of power, you must replace the backup battery to ensure reliable operation. This backup battery acts as a storage container that holds enough energy to maintain the settings and programming on your security system if the power supply is disrupted. This can also help protect your unit from technical problems or faulty wiring that occurs during a lightning storm, helping to keep it functioning correctly.

Before replacing the batteries in your Bosch alarm system, please read all steps carefully as mistakes can lead to serious problems. You will need one 9V standard alkaline battery and be sure to check its expiration date before usage. Before replacing or removing any parts of the system, always remember to unplug and switch off all main power sources for safety reasons.

Once you have prepared a new 9V standard alkaline battery and unplugged all main sources of power, carefully remove each of the components from their port using a Phillips screwdriver – this includes both external speaker cabling and internal cabling too – then unscrew both screws on the back of control panel which have been securing it in place; next locate slots marked ‘back-up’ which will house two new 9V standard alkaline batteries; lastly correct placement requires these two new batteries inserted into socket at right angle making certain cable never bent too sharp (to avoid damage). Now reassemble components and test unit before continuing with installation process according to manufacturers instructions.

Once installed again you may use main power source with no risk but always remembering to replace 9V standard alkaline batteries every two years for optimal performance.

Plug the power cord back into the wall outlet

To re-connect the power source to your Bosch alarm system, begin by locating the power box. This is the main control panel for your system, which is usually located close to the entry/exit points at your home. Once you have located the power box, plug the included power cable into its designated slot in order for it to resume operation.

The next step is to plug the other end of this cable into a wall outlet. Make sure that this wall outlet is properly grounded and secure; any loose or exposed wiring can pose a safety risk to both you and your security system. Also make sure that this outlet has enough space around it so that once plugged in, there are no items blocking the connection or restricting access. Lastly, be sure that the voltage is suitable for powering up your home alarm system – if necessary, refer to its manual or refer back to a qualified technician for assistance if needed.

Test the System

Testing your Bosch alarm system is a crucial step in the reset process. It is important to check the system after each step to make sure the reset has been successful. If the system is not working properly, this could be an indication that the reset was not successful. To test the system, make sure all the sensors are working properly and that the control panel is detecting any changes. Check that the siren is working, too. If any of the tests fail, try restarting the reset process.

Activate the alarm system

Activating your Bosch alarm system is the first step in setting up your home security system. To begin, locate the Control Panel. This is typically a touch-screen device mounted on a wall near the entrance to your home or office.

Next, switch the main power supply to “On” using either a key or password (depending on your model). You can find out which key or password you need in the product’s manual, which is available from the manufacturer’s website. Once complete, you should hear a single beep indicating that it has powered up correctly.

Then, enter in your system code. Make sure this code is kept private as it prevents unauthorized access to your system settings and features. Now enter in any regional codes required for your area – these codes vary depending on where you live and are usually designated by county or zip code.

Finally, press “1” followed by the star (*) key on the control panel to activate the alarm system. Your system will then perform an initial test cycle to confirm that all sensors and detectors are working properly before fully activating itself – this could take up to five minutes depending on how many solutions are installed within your property. After this test runs its course, you will see a green indicator light appear on the control panel confirming that your Bosch alarm system is now active!

Test all the sensors

Before concluding any troubleshooting, it’s important to test every single sensor in the system. Completing this task will ensure that all components are functioning properly and alert you if any sensors need additional attention. To start, turn off the Bosch alarm and then unplug the power cord.

Next, detach each sensor from the wall and reattach it as though you were repairing it or replacing its battery. During this process, press and release the “Test” button on each device to ensure that its signal functions properly with your control panel. This process should be done for motion detectors, door/window contacts, smoke detectors, temperature sensors and flood detectors (if applicable).

Now that each sensor has been tested individually, engage a “System Test” by connecting your link cable or wireless communication method between your main control panel and keypad or remote contact device. You may need to enter special commands or use a specific sequence of keys depending on which devices are currently connected – see your owner’s manual for specific instructions. If all sensors test successfully during this System Test then you can be confident in resetting your Bosch alarm system back online!

Test the keypad

Testing the keypad is an important step in ensuring that your Bosch alarm system is configured correctly. Once you have finished setting up your system, it is important to properly test it to ensure that the keypad and all of the components are working correctly. Testing the keypad will allow you to confirm that it is detecting your inputs and displaying messages appropriately.

To test the keypad, enter four digits (any numbers) on your keypad and press “#” or the checkmark button. Your alarm system should beep three times and display a confirmation message on the LCD screen stating “Completed – Entry Accepted”. This confirms that your entry has been accepted and indicates that the system is functioning properly.

After testing your keypad, you should exit back to Off mode before leaving for work or going out for extended periods of time. To do this, press “Set” followed by 01 (four digit code) # (or press checkmark). The LCD screen will then display “Exited” indicating that you have successfully exited from Away Mode.

How to Reset Your Bosch Alarm SystemCheckout this video:

Share this Article