Skip to content

How to Reset Your Honda Jazz Alarm System

This article is a collaborative effort, crafted and edited by a team of dedicated professionals.

Contributors: Muhammad Baballe Ahmad, Mehmet Cavas, Sudhir Chitnis, and Zhen-ya Liu.

✓ Verified & Tested Information

If your Honda Jazz alarm system goes off, it can be reset using these simple steps.

Preparation

When resetting your Honda Jazz alarm system, you need to do a few things to make sure it goes smoothly. First, you should gather all the materials and tools you need: a flathead screwdriver, a Phillips screwdriver, a socket wrench set, a ten-millimeter nut, and some electrical tape. Make sure that you have all these items before beginning the reset process. Next, take a look at your car’s manual and make sure you understand the alarm system’s wiring diagram. This will help you identify potential problems before they arise.

Disconnect the battery

One of the necessary steps for resetting your Honda Jazz alarm system is to disconnect the battery. This should be done by a certified technician in order to ensure everything is done safely and correctly. Before doing this step, make sure to turn off all other systems in the car, such as air conditioning and ignition. If you are unsure about how to do this, consult your owner’s manual or a qualified technician.

To disconnect the battery, start by locating the positive terminal (red wire) and removing it from its post. Next, open the hood and locate the negative terminal (black wire) and remove it from its post as well. Ensure both connections are completely disconnected before proceeding with resetting your alarm system.

Locate the alarm fuse

It is important to locate the alarm fuse in order to properly reset your Honda Jazz alarm system. In order to locate the alarm fuse, you will need to first remove the cover of your main fuse box, located on the driver’s side of the engine compartment. Within this box, you will find a variety of slots – each labeled with its particular purpose. Once identified, gently remove the alarm fuse and set it aside for later re-installation. Be sure not to disconnect any other fuses as this can cause further unanticipated damage. Once removed, proceed with resetting the alarm system per manufacturer guidelines.

Resetting the Alarm

Resetting the Honda Jazz alarm system is not an overly complicated process, but it is something that should be done with care. There are a few steps to follow in order to reset the alarm successfully, so it is important to follow the instructions closely. After resetting the alarm, you will be able to enjoy the peace of mind that comes with having your car safe and secure. Let’s get started.

Remove the alarm fuse

In order to reset your Honda Jazz’s alarm system, the first step you need to take is to remove the alarm fuse from the fuse box. This is typically located in the engine compartment, either near the battery or accessibly through a panel on one side of the engine. If you have trouble locating it, you can consult your car’s owner’s manual for exact locations and specific instructions on how to remove it.
Once you have found and removed the alarm fuse, you should turn off all other electrical components in your Honda Jazz before beginning the reset process. This includes lights, windows and other accessories that may be draining power from the system. After powering off all other devices, go ahead and secure all vehicle doors with their respective locks and insert your key into the ignition switch.

Next, turn on only one key position while keeping the others off – this will allow current to reach only a small portion of circuits related to your Honda Jazz’s electrical system; this is necessary for successful resetting. With this in place, press any of buttons located on both sides of your regular remote control followed by pressing another button twice within a few seconds – these could either be start buttons located near each door handle or lock/unlock buttons located on different areas of your remote control unit. Finally reinsert both fuses into their appropriate spots – this will successfully reset your Honda Jazz’s alarm system with time to spare!

Wait for 5 minutes

Once you have the alarm system disabled, you need to wait for 5 minutes. During this time, your Honda Jazz will temporarily turn off its security system in order to ensure that it is properly reset. Be sure that the car is turned off and you are away from the vehicle during this time. If somebody does try to break in or tamper with your car, a message will be sent to the onboard computer and the alarm system will be automatically reset again. It is important to wait for at least 5 minutes before continuing with the reset.

Reinsert the fuse

Once you have identified the alarm system fuse, carefully remove the fuse and wait for 15 seconds. After this period of time has passed, reinsert tthe fuse carefully into its original place. Once the fuse is correctly and securely in place, turn the ignition switch on to off, and then back on again. The alarm system will no longer be activated and should reset itself.

If you find that your car alarm still does not work after performing this step, it may be because of a more complex problem in your vehicle’s electricalsystem. In such a case, it is best to take your car to a qualified technician for repair. They will be able to diagnose the exact cause of the problem and get it fixed for you quickly and effectively.

Testing the Alarm

Resetting the Honda Jazz alarm system requires that you first test the alarm to make sure it is working properly. In order to do this, you will need to open all the doors and disable the interior light, as well as turn off any interior electronics such as the radio. Once this has been completed, you can then proceed with testing the alarm by setting off the triggers.

Reconnect the battery

Reconnecting the battery is a simple process, but you should take care to minimize any risk of harm. Before reconnecting, make sure the ignition key is removed from the vehicle’s system. Turn the key to the accessory position and remove the red positive terminal clamp from its post on the battery first. Make sure all accessories in your Honda Jazz that were powered by the battery are off. Then, connect the cable back onto its post on the battery and only then replace the red positive terminal clamp in order for your alarm system to be reset. For added safety, you can also use an insulating material on either end of each cable when connecting or disconnecting your battery.

Test the alarm system

Testing your Honda Jazz alarm system is a hassle-free process that helps verify that your security system is functioning as intended. To test the alarm system, ensure the following steps are taken:

1. Ensure the doors are closed and locked.
2. Activate the alarm by pressing the lock button on your remote control several times rapidly.
3. The siren should sound for about 3 seconds and then stop, signaling the alarm system has been activated properly.
4. Check to confirm that all of the lights have turned off after activating the alarm system. This indicates that all sensors have been set correctly and will protect your Honda Jazz from any intruders or attempts at intrusion.
5. A few seconds after activation, press and hold down both LOCK and UNLOCK buttons on your remote control simultaneously for about 5 seconds until you hear a chirping sound twice in succession indicating successful deactivation of the alarm system upon each successful chirp sequence completion.
6. If you find an issue with any of these steps, it is recommended to visit a local authorized repairer to help diagnose or rectify any underlying issues with your security system; this could save you incurring costly repair bills in future due to attempted break ins or other issues with faulty protective systems within your vehicle’s safety infrastructure such as faulty window locks etc., which should be addressed as they appear or arise in order to avoid costly repairs or vehicle damage in future due to attempted theft etc..

Troubleshooting

When an issue arises with your Honda Jazz alarm system, it can be difficult to identify and rectify the problem. Troubleshooting your system may involve identifying any faults in the wiring, checking the batteries of the sensors, or verifying the correct connection of the modules. In this section, we will look at the most common issues that can arise with the Honda Jazz alarm system, as well as how to resolve them.

Check the alarm fuse

The first step in troubleshooting the Honda Jazz alarm system is to check the fuse associated with it. The exact location of the fuse varies based on mode year and trim level, so consult your user manual for specifics. Once you locate the correct fuse, simply pull it out and inspect it for visible signs of damage. If you do find any, then replace the fuse with a new one that has the same specs as the original. Be sure to also check all adjacent fuses for damage; if your car experiences frequent electrical problems, then a ‘bad’ fuse may be a cause. Once all fuses have been inspected and/or replaced, you can proceed to resetting your alarm system.

Check the wiring

Before troubleshooting any Honda Jazz alarm system, ensure that the wiring is correctly connected to the battery of your car. To do this, examine each connection carefully and make sure that there are no loose or corroded wires. If any suspect wires are found, repair them before attempting to reset the alarm system. Additionally, inspect all Door Trigger Wires and unhook them to avoid false triggering of the Honda Jazz security system. Take note of where the wiring goes and make sure that it is in its correct place after making these adjustments.

Check the alarm module

Before attempting to reset your Honda Jazz alarm system, you should first make sure that the alarm module is functioning properly. This can be done by checking the following components:

-Check the connection between the alarm module and the factory wiring. Make sure all connections are secure and not corroded.
-Open up the Honda Jazz’s bonnet and inspect the ground connection to ensure it is tightly secure. A loose connection could prevent your alarm system from working properly.
-Check that all of your car’s ground leads (i.e., those connected to mounting studs) are in good condition and firmly attached to their points of connection on the vehicle frame or engine compartment.
-Inspect each wire in your car’s harness for signs of wear or damage, as well as corrosion, which could render a connection unreliable or cause a short circuit. Any faulty wiring should be replaced with new wires before attempting to reset your Honda Jazz Alarm System.

How to Reset Your Honda Jazz Alarm SystemCheckout this video:

Share this Article