Skip to content

How to Reset Your Visonic Alarm System

This article is a collaborative effort, crafted and edited by a team of dedicated professionals.

Contributors: Muhammad Baballe Ahmad, Mehmet Cavas, Sudhir Chitnis, and Zhen-ya Liu.

✓ Verified & Tested Information

If you need to know how to reset your Visonic alarm system , this blog post will show you the step-by-step process.

Preparation

Before you can reset your Visonic alarm system, there are a few things you’ll need to do first. Firstly, make sure that the alarm is turned off and that the batteries have been replaced. Secondly, you’ll need to get the programming manual for your system so you can follow the instructions carefully. Lastly, you’ll need to have all your codes and passwords for your system at hand. Now, you’re ready to start the reset process.

Gather the necessary tools

Before resetting your Visonic powermax alarm system, you will need to gather all the necessary tools for the job. Make sure to have a well-charged Philips-head screwdriver, a 2.5 mm Allen wrench, a 9V battery and a fresh backup battery ready for installation. You may also need some electrical tape, depending on where you place the wiring and your home’s construction type. Ensure you have access to all the necessary outlets or wiring before beginning the reset process. Additionally, if you are uninstalling or replacing any part of the system (including sensors), make sure these parts are readily accessible as well.

Make sure the power is off

Before attempting to reset your Visonic alarm system, ensure that the circuit breakers that control the power to your alarm are switched off. Switching off the power will help prevent any setting changes or activation of alarms while you are attempting to reset. If you’re unsure which circuit breaker controls the power, try switching off each one in turn until you no longer hear a noise coming from your alarm system. Once you’ve found the correct breaker, snap it firmly into the “Off” position.

Once all power to your Visonic alarm system has been disconnected, proceed with resetting your device. Make sure not to reconnect any circuit breakers until after resetting has been completed or your settings will be overridden.

Disconnect the alarm system

Disconnect the alarm system from the power. You can do this by unplugging the transformer from the wall outlet. The transformer is usually located near the main control panel of the security system, which is usually found inside the house. Do not disconnect any wires that are connected to this component as doing so may cause serious damage to your security system and will require technical assistance to repair.
Disable any keyfobs or remotes that you may have been using with your alarm system by pressing and holding a button located on each device for several seconds or until a beep is heard. You should also remove all batteries from each of your remotes and keyfobs in order to ensure they are reset properly and won’t inadvertently activate your alarm system during resetting or testing stages.

Resetting the Master Code

Resetting your Visonic alarm system’s master code is an important step in resetting, configuring, and troubleshooting your system. It ensures that only users with the correct access code can enter, arm, and disarm the system. The process of resetting the master code is straightforward and can be done in a few steps. In this article, we’ll review the steps to resetting the master code and provide tips and best practices to keep your system secure.

Find the reset button

To reset the Master Code on a Visonic alarm system, you’ll need to locate the Reset Button located in the Control Panel. The Control Panel is typically installed near the entrance of the property and may require a professional installer to access. Once you have located the Reset Button, press it firmly and hold for at least five seconds until you hear a ‘beep’ sound. This will reset the Master Code for your system.
It’s important to note that you should reset your code regularly for security purposes, as well as if you experience any issues with your security system. It’s also recommended that you never use any variation of the word ‘code’ when setting up or changing the Master Code. To make sure that your security is properly maintained, keep an up-to-date master code and always make sure it is secure and not written down in an easy-to-find place where others can gain access to it.

Press and hold the reset button

To reset the master code of your Visonic alarm system, follow these steps:
1. Find the reset button, usually on either the back or side of the main console.
2. Press and hold the reset button down for around five seconds. You should hear a confirmation tone from the device that indicates that the master code has been reset successfully.
3. Enter in a new four or six digit master code and press ‘Enter’ or ‘OK’ to set it. Make sure to remember this code for future use.
4. Test your new master code to ensure it is working as designed before you exit out of the programming menu, which can be done simply by entering in your new master code on either keypad or app-based command systems associated with your alarm system.

Now, to prevent unauthorized access to your alarm system and its functions, make sure that all family members know not to share their newly created master codes with any unverified users outside of their home environments.

Enter the new master code

After you have undone the metal cover, Locate the master reset button. Once this is done, a green light should appear. This is indicating that it is ready to accept a new code. Enter the new master code three times, pressing ‘*’ after each code as confirmation that it has been entered correctly. Upon successful acceptance of your new master code, a chime will be heard and the door lock light will flash four times. Don’t forget to replace the metal cover!

Resetting the User Codes

Resetting the user codes on your Visonic alarm system is an important task if you want to ensure the security of your home. Disarm the system and assign new user codes for family members, friends, or any other authorized person. It is also important to reset the user codes periodically to prevent unauthorized access to your home. In this section, we will explain how to disarm the system and reset the user codes on your Visonic alarm system.

Find the reset button

If you are having difficulty resetting your Visonic security system, it is possible that the user codes have been corrupted. To reset the user codes to factory settings, begin by locating the reset button. On most models, the reset button is located on the main board and covered by a small plastic tab. Press and hold down the reset button for at least 15 seconds until all LEDs light up. This will cause all user codes stored in the alarm system to be erased, allowing you to start from scratch with new user codes.

When you have completed this step, refer to your model’s manual for instructions on how to correctly program new user codes into your security system. If you experience any additional difficulties or require assistance understanding any of these steps, please contact Visonic customer service or a qualified professional and they will be happy to help.

Press and hold the reset button

Resetting the user codes on your Visonic alarm system is as easy as pressing and holding the reset button on the keypad. To ensure it is completed successfully, there are a few steps that must be followed.

First, make sure the system is armed. Next, press and hold the reset button for at least 3 seconds until you hear two beeps. After those two beeps, enter a four-digit code twice in succession to confirm it has been successfully changed.

Lastly, press # to exit programming mode and return to normal operation for your system. It’s important to note that by resetting the code you are essentially wiping out previous codes from the system and any users who had previously gained access will no longer have access after this step has been completed. It is also important to ensure all of these steps are taken with care and precision so that none of your system’s settings are affected accidently or otherwise during this process.

Enter the new user codes

To enter new user codes, you’ll need to activate the programming mode of the Visonic alarm system. Once in programming mode, follow these steps:

1.Enter the master code followed by [#].
2.Press [8] to enter system setup.
3.Press [9] twice to enter user code programming menu.
4.Enter a 4-digit number for the new user code you want to add in the system, then press [#]. Make sure that your selection does not match with any of the existing users or with any other master codes.
5.The system will provide an audible confirmation and will indicate how many user codes have been stored in it so far if applicable.
6.Follow these same steps until all required users are added or deleted from the list of authorized users of your Visonic alarm system, if necessary.
7.[##] will exit this programming menu and return you to standby mode when finished

Reconnecting the Alarm System

Resetting your Visonic alarm system can be a fairly straightforward process. Before you begin, make sure that the power is disconnected from the system. Then you can begin to reset the alarm system by disconnecting its sensors and keypad. Next, you need to reconnect all the components again, so they are working together in sync. Let’s take a look at the steps you need to take to reset your Visonic alarm system.

Connect the alarm system

Before proceeding, you will need a basic understanding of electrical circuits and the ability to read a wiring diagram. If you do not feel comfortable working with wiring, please call a professional electrician for assistance in connecting the alarm system.

Connect the components of your Visonic alarms as per the provided wiring diagram. Make sure that all connections are tight and secure. When finished, connect the main power supply to your control panel and plug it into an outlet that is part of your home’s electrical system. It is important to note that not all power sources are compatible with Visonic alarms. Refer to your operating instructions for details on the acceptable voltage ratings for your particular model.

Once connected, you will need to turn on all circuit breakers associated with your alarm system in order for it to function correctly. Check the system by testing each area of coverage (doors, windows, etc.) and ensure that they operate properly when triggered by movement or contact with entry points. After these checks have been completed, finalize installation by programming user codes into the control panel according to manufacturer’s instructions.

Turn on the power

Before attempting to reset your Visonic alarm system, it is important to ensure that you have access to the correct power source. Some Visonic alarm systems require you to use an AC outlet for power in order for the system to operate correctly.

First, locate the main power switch on your control panel. This switch is usually located on the back of the control panel and should be clearly labeled. Turning this switch to “on” will provide power to the panel’s components and allow you to begin resetting your system. Normally, when you receive a low battery warning, all components of your Visonic alarm system will turn off until you manually turn it back on.

Once power is connected between your alarm system and its control panel, test the system’s functionality by entering a test code into the keypad and pressing “reset”. The reset step serves as a way of setting up your security preferences after turning on the power. Verify that all sensors are functioning correctly by conducting several tests with them.

Test the alarm system

Testing the alarm system is an important step to ensure that it is in proper working order after resetting and reconnecting all of your components. To do this, you should check two main areas:

1. Secure all doors and windows to ensure that the system is properly armed – you may also want to run a test to check for false alarms.

2. Make sure the control panel is updated with any new information including user codes and sensor locations.

After running these tests, check that all components of the system are in programmed mode. Doing this will ensure that your security system will function properly in the future when it is triggered by a real threat or alert.

How to Reset Your Visonic Alarm SystemCheckout this video:

Share this Article